ENGINE

To Our Customers:
After 70 plus years of trouble free, metal-to-metal engine protection, the E.P.A. is forcing ZDDP ( Zinc Dialkyl-Dithio-Phosphate ) to be drastically lowered from domestic motor oil, to protect catalytic converters.

Our Opel engines were designed with conventional solid or hydraulic flat tappet lifters which require higher levels of the friction modifier ZDDP in the engine oil to avoid premature cam and lifter deterioration. Opel specified ‘SE’ high quality engine oils and made specific mention to use detergent oils. The modern ‘SM’ grade oils have greatly reduced amounts of these Opel specified qualities.

Opel GT Source recommends the use of ZDDP Plus to be added with each oil change, and If you are rebuilding your engine, we recommend Comp Cams Break-In oil additive for engine break-in protection.

ZDDP & BREAK-IN ADDITIVES
6170 COMP CAMS ENGINE BREAK-IN ADDITIVE
12-ounce bottle of Engine Break-In Oil Additive. Use anytime you replace a cam, lifters or rebuild an engine.		 15.00
6171 ZDDP PLUS
4-ounce bottle of ZDDP Plus oil additive. Use everytime you change your engine oil.		 15.00
TUNE UP COMPONENTS & ELECTRONIC IGNITION CONVERSION
1.9L Engines 1968-75
6042 CONTACT POINTS
Ignition contact points, for 1968-1974 distributers.		 9.00
6134 CONTACT POINTS
Ignition contact points,for 1975 FI dsitributor.		 9.00
6043 CONDENSER
Condenser for igniton points.		 11.00
6040 CHAMPION SPARK PLUG
champion spark plug. Four (4) required.
Available for 1968-1970 engines L82YC & 1971-1975 engines L87YC.		 2.00
each
6077 BOSCH PLATINUM SPARK PLUG
Set of four (4) Bosch Platinum spark plugs.		 12.00
set
6163 NGK SPARK PLUGS
Set of four (4) NGK spark plugs.		 12.00
set
6041 DISTRIBUTOR CAP AND ROTOR
Cap & Rotor for 1970 thru 1975 1.9L distributers.		 19.00
6041 69 DISTRIBUTOR CAP AND ROTOR
Cap & Rotor for 1968 & 1969 distributers.
Distributer Case #: 0 231 167 005		 19.00
6071 IGNlTlON WIRE SET
Pre-cut spark plug and coil wires. 1.9L-2.4L.		 20.00
set
6078 DISTRIBUTOR CAP, COLORED
Transparent yellow, blue or red. Specify color. For 1970-1973.		 9.50
6152 SPARK PLUG WIRE ROUTER
Spark plug wire router for your Opel engine, 1.9L-2.4L. Original 2.4L Opel part.		 15.00
6165 PERTRONICS POINTS CONVERSION IGNITION
Electronically controlled ignition trigger that eliminates the need for points and condensor improves throttle response. Simplifies tune-ups, gets rid of the points forever! Easy to install.		 99.00
6039 OIL FILTER
High quality oil filter.		 8.50
6039KN K&N OIL FILTER
K&N Performance Gold oil filter.		 15.00
1.9L GASKETS & SEALS
1968-72 10-Bolt Cylinder Head type
6002 COMPLETE GASKET SET
1968-1972, 1.9L with 10 bolt head gasket.		 139.00
6004 HEAD GASKET SET
1968-1972, 1.9L with 10 bolt head gasket.		 77.00
6006 INTAKE/EXHAUST GASKET
Intake/exhaust to cylinder head, 1.9L.(Also fits 1.5L & 2.0L)		 13.00
6007 EXHAUST TO INTAKE GASKET
Between the intake and exhaust manifolds (hot spot gasket), 1.9L.		 2.50
9004 GASKET CARBURETOR TO INTAKE MANIFOLD
Carburetor to intake manifold, thick gasket with plastic eyes to prevent carburetor base plate warping. Helps reduce vacuum leaks.
NOTE: You will also need 9018 if your engine is equipped with a heatshield under the carburetor.		 9.00
9018 GASKET HEAT SHIELD TO INTAKE MANIFOLD
Carburetor heat shield to intake manifold, thin.
NOTE: You may also need 9004.		 4.00
6008 VALVE COVER GASKET
Valve cover to the cylinder head. Specify year if other than GT 1900 with aluminum valve cover.		 11.00
6009 OIL PAN GASKET
Oil pan to block. 1.5L-2.4L.		 16.00
6010 WATER PUMP GASKET
Water pump to timing cover. 		5.60
6011 OIL PUMP GASKET
Oil pump cover to timing cover.		 2.40
6012 TIMING COVER GASKETS
Timing cover to block.		 12.00
set
6013 THERMOSTAT GASKET
Fits around thermostat.		 1.50
6014 THERMOSTAT HOUSING GASKET
Thermostat housing to cylinder head. 		2.40
6015 CAM COVER GASKET
Cam cover to head. Front or rear.		 3.00
6016 HEAD SIDE PLATE GASKET
Side plate to head.		 2.00
6017 FUEL PUMP GASKET
Fuel pump to timing cover. Two (2) required.		 1.20
each
6018 FRONT SEAL
Timing cover to pulley.		 12.00
6019 REAR MAIN SEAL 24.00
6020 O-RING SEAL
Timing cover to head, rubber.		 2.40
6051 FUEL PUMP SPACER
Spacer for between fuel pump and timing cover.		 6.60
6065 HEAD GASKET
1968-1972, 1.9L. Ten (10) bolt.		 37.00
6070 BOTTOM END GASKET SET
Includes oil pan gaskets, timing cover gaskets, front and rear main seals, fuel pump gaskets and spacer, water pump gasket, oil pick-up gasket, distributor gasket and oil pump gasket.		 65.00
6075 DISTRIBUTOR GASKET
Between timing cover and distributor.		 1.20
6089 INTAKE VALVE SEAL
Special performance cup type valve seal intake valve. Four (4) required, used 1970-1975.		 7.20
each
6098 TIMING COVER GASKET SET
Includes front seal, water pump gasket and timing cover gasket set.		 25.00
6131 FRONT PULLEY SLEEVE REPAIR KIT
Helps prevent serious oil leaks cause by a grooved pulley shaft.		 8.00
10012 HEADER GASKET
Special REMFLEX high-temp gasket for early-style headers.		 45.00
1.9L GASKETS & SEALS
1972-1975 12-Bolt Cylinder Head type
6003 COMPLETE GASKET SET
1973-1975, 1.9L with twelve (12) bolt head gasket.		 135.00
6005 HEAD GASKET SET
1973-1975, 1.9L with twelve (12) bolt head gasket.		 79.00
6006 INTAKE/EXHAUST GASKET
Intake/exhaust to cylinder head gasket, for 1.9L Also fits 1.5L & 2.0L.		 13.00
6007 EXHAUST TO INTAKE GASKET
Between the intake and exhaust manifolds (hot spot gasket), 1.9L.		 2.50
9004 GASKET CARBURETOR TO INTAKE MANIFOLD
Carburetor to intake manifold, thick gasket with plastic eyes to prevent carburetor base plate warping. Helps reduce vacuum leaks.
NOTE: You will also need 9018 if your engine is equipped with a heatshield under the carburetor.		 9.00
9018 GASKET HEAT SHIELD TO INTAKE MANIFOLD
Carburetor heat shield to intake manifold, thin.
NOTE: You may also need 9004.		 4.00
6008 VALVE COVER GASKET
Valve cover to the cylinder head. Specify year if other than GT 1900 with aluminum valve cover.		 11.00
6009 OIL PAN GASKET
Oil pan to block. 1.5L-2.4L.		 16.00
6010 WATER PUMP GASKET
Water pump to timing cover. 		5.60
6011 OIL PUMP GASKET
Oil pump cover to timing cover.		 2.40
6012 TIMING COVER GASKETS
Timing cover to block.		 12.00
set
6013 THERMOSTAT GASKET
Fits around thermostat.		 1.50
6014 THERMOSTAT HOUSING GASKET
Thermostat housing to cylinder head. 		2.40
6015 CAM COVER GASKET
Cam cover to head. Front or rear.		 3.00
6016 HEAD SIDE PLATE GASKET
Side plate to head.		 2.00
6017 FUEL PUMP GASKET
Fuel pump to timing cover. Two (2) required.		 1.20
each
6018 FRONT SEAL
Timing cover to pulley.		 12.00
6019 REAR MAIN SEAL 24.00
6020 O-RING SEAL
Timing cover to head, rubber.		 2.40
6051 FUEL PUMP SPACER
Spacer for between fuel pump and timing cover.		 6.60
6066 HEAD GASKET
1973-1975, 1.9L for twelve (12) bolt head. 		39.00
6070 BOTTOM END GASKET SET
Includes oil pan gaskets, timing cover gaskets, front and rear main seals, fuel pump gaskets and spacer, water pump gasket, oil pick-up gasket, distributor gasket and oil pump gasket.		 65.00
6075 DISTRIBUTOR GASKET
Between timing cover and distributor.		 1.20
6089 INTAKE VALVE SEAL
Special performance cup type valve seal intake valve. Four (4) required, used 1970-1975.		 7.20
each
6098 TIMING COVER GASKET SET
Includes front seal, water pump gasket and timing cover gasket set.		 25.00
6131 FRONT PULLEY SLEEVE REPAIR KIT
Helps prevent serious oil leaks cause by a grooved pulley shaft.		 8.00
10012 HEADER GASKET
Special REMFLEX high-temp gasket for early-style headers.		 45.00
2.0L GASKETS & SEALS
1976-1989 2.0L 12-Bolt Cylinder Head type
6006 INTAKE/EXHAUST GASKET
Intake/exhaust to cylinder head gasket, for 2.0L.Also fits 1.5L & 1.9L		 13.00
6008 VALVE COVER GASKET
Valve cover to the cylinder head. Specify year if other than GT 1900 with aluminum valve cover.		 11.00
6009 OIL PAN GASKET
Oil pan to block. 1.5L-2.4L.		 16.00
6010 WATER PUMP GASKET
Water pump to timing cover. 		5.60
6012 TIMING COVER GASKETS
Timing cover to block.		 12.00
set
6013 THERMOSTAT GASKET
Fits around thermostat.		 1.50
6014 THERMOSTAT HOUSING GASKET
Thermostat housing to cylinder head, for 2.0L with carbureted thermostat housing. 		2.40
16007 THERMOSTAT HOUSING GASKET
Thermostat housing to cylinder head, 2.0L with fuel injection thermostat housing.		 2.40
6015 CAM COVER GASKET
Cam cover to head. Front or rear.		 3.00
6016 HEAD SIDE PLATE GASKET
Side plate to head.		 2.00
6018 FRONT SEAL
Timing cover to pulley.		 12.00
6019 REAR MAIN SEAL 24.00
6020 O-RING SEAL
Timing cover to head, rubber.		 2.40
6068 HEAD GASKET
1976-1989, 2.0L. Twelve (12) bolt.		 58.80
6070 BOTTOM END GASKET SET
Includes oil pan gaskets, timing cover gaskets, front and rear main seals, fuel pump gaskets and spacer, water pump gasket, oil pick-up gasket, distributor gasket and oil pump gasket.		 65.00
6075 DISTRIBUTOR GASKET
Between timing cover and distributor.		 1.20
6089 INTAKE VALVE SEAL
Special performance cup type valve seal intake valve. Four (4) required, used 1970-1975.		 7.20
each
6098 TIMING COVER GASKET SET
Includes front seal, water pump gasket and timing cover gasket set.		 25.00
6131 FRONT PULLEY SLEEVE REPAIR KIT
Helps prevent serious oil leaks cause by a grooved pulley shaft.		 8.00
6188 HEAD GASKET SET
1976-1991, 2.0L with twelve (12) bolt head gasket.		 114.00
10012 HEADER GASKET
Special REMFLEX high-temp gasket for early-style headers.		 45.00
2.2L & 2.4L GASKETS & SEAL
2.2L, 1983-1989 12-Bolt Cylinder Head type
2.4L 1988-1995 12-Bolt Cylinder Head type
6147 HEAD GASKET SET
2.2L-2.4L		 130.00
6148 FULL GASKET SET
2.2L-2.4L 		180.00
6008 VALVE COVER GASKET, w/ GT VALVE COVER
If you are running a stock GT alumiunum valve cover on your 2.2L or 2.4L, order this gasket.		 11.00
6008S VALVE COVER GASKET, 2.2L EFI VALVE COVER
If you are running the 2.2L EFI alumiunum valve on your 2.2L, order this gasket.		 11.00
6009 OIL PAN GASKET
Oil pan to block. 1.5L-2.4L.		 16.00
6010 WATER PUMP GASKET
Water pump to timing cover. 		5.60
6012 TIMING COVER GASKETS
Timing cover to block.		 12.00
set
6015 CAM COVER GASKET
Cam cover to head. Front or rear.		 3.00
6016 HEAD SIDE PLATE GASKET
Side plate to head.		 2.00
6018 FRONT SEAL
Timing cover to pulley.		 12.00
6019 REAR MAIN SEAL 24.00
6020 O-RING SEAL
Timing cover to head, rubber.		 2.40
6068 HEAD GASKET
1976-1989, 2.0L. Twelve (12) bolt.		 58.80
6070 BOTTOM END GASKET SET
Includes oil pan gaskets, timing cover gaskets, front and rear main seals, fuel pump gaskets and spacer, water pump gasket, oil pick-up gasket, distributor gasket and oil pump gasket.		 65.00
6075 DISTRIBUTOR GASKET
Between timing cover and distributor.		 1.20
6089 INTAKE VALVE SEAL
Special performance cup type valve seal intake valve. Four (4) required, used 1970-1975.		 7.20
each
6098 TIMING COVER GASKET SET
Includes front seal, water pump gasket and timing cover gasket set.		 25.00
6131 FRONT PULLEY SLEEVE REPAIR KIT
Helps prevent serious oil leaks cause by a grooved pulley shaft.		 8.00
6137 THERMOSTAT HOUSING GASKET
2.2L-2.4L thermostat housing to cylinder head.		 2.40
6138 INTAKE/EXHAUST GASKET
2.2L-2.4L intake/exhaust to cylinder head.		 22.00
6139 HEADER GASKET
Made from high-temp Remflex material. For 2.2L-2.4L intake/exhaust.		 45.00
6144 ALUMINUM VALVE COVER
2.2L, black with machined top surface. "2.2 INJECTION" on top. NOS, Limited Stock.		 175.00
16018 THERMOSTAT "O" RING
2.2L-2.4L.		 5.00
ENGINE - PISTONS & RINGS
For: 1.5L, 1.9L & 2.0L engines
6052 1.9L PISTONS, 93mm
1.9L 9.0 : 1 Compression Pistons, with rings and pin.
Avaialable sizes: Standard, 0.020" (.50mm), 0.030" (.75mm) & 0.040 (1.0mm).		 95.00
each
6053 1.9L PISTON RINGS, 93mm
1.9L Piston Rings, set of four (4).
Available sizes: Standard, 0.020" (.50mm), 0.030" (.75mm) & 0.040 (1.0mm).		 45.00
set
6132 2.0L PISTONS, 95mm
2.0L 9.4:1 Compression Pistons, with rings and pins. Size: Standard.
Build your 1.9L into a 2.0L using these pistons. Giving you 9.4:1 compression with a standard 1.9L cylinder head.		 380.00
set
6140 2.0L PISTON RINGS, 95mm
2.0L, size STD. Set of four (4).		 60.00
set
6142 2.2L PISTON RINGS, 95mm
2.2L, size STD. Set of four (4)		 80.00
set
6133 1.5L PISTONS
1.5L, size .5mm (.020"). Set of four(4).		 250.00
set
ENGINE - BEARINGS
1.9L, 2.0L, 2.2L & 2.4L
6054 ROD BEARINGS
Rod Bearing set for 1.5L, 1.9L, 2.0L, & 2.2L
Avaialble sizes: Standard, 0.010" (.25mm), 0.020" (.50mm) & 0.030" (.75mm).		 45.00
set
6055 MAIN BEARINGS
Main Bearing set for 1.5L, 1.9L, 2.0L, 2.2L & 2.4L
Available sizes: Standard, 0.010" (.25mm), 0.020" (.50mm), 0.030" (.75mm) & 0.040" (1.0mm).		 90.00
set
6045 CAM BEARINGS
Cam Bearing, set. Fitiing 1971 thru 1975 cylinder heads. Finsihed.		 45.00
set
6045D CAM BEARINGS, DELTA
Cam Bearing, set. Fitting 1969 & 1970 cylinder heads with the 'Delta' marking. Finsihed.		 45.00
set
6046 CAM BEARINGS, NON-DELTA
Cam Bearing set. Fitting 1969 & 1970 cylinder heads that do not have the 'Delta' marking. Semi-Finsihed, must be align-bored.		 45.00
set
Engine block
Hardware & seals
6018 SEAL, FRONT
Timing cover to pulley.		 12.00
6019 SEAL, REAR MAIN.
 24.00
6044 OIL PRESSURE SENDER
New original Opel part. With rubber boot. 		126.00
6067 BOLT, CONNECTING ROD
1.9L.		 9.00
each
6069 BOLT, FLYWHEEL TO CRANK
1.9L-2.2L. Attaching bolts. Six (6) required.		 4.20
each
6074 DIP STICK
New. Late 1971-1975 with steel oil pan only. 1.9L-2.4L.		 18.00
6079 OIL PRESSURE SENDER, VDO
OEM replacement part. Without rubber boot. 		129.00
6082 BRACKET
2.4L oil pick-up tube for steel oil pan. Specially designed to clear 2.4L crankshaft counterweights. It will also work with 1.9L steel oil pan pickup tube.		 7.20
6085 DOWEL PIN
Block to head alignment.		 2.40
each
6086 PLUG
13mm dipstick hole.		 3.60
each
6101 BOLT, FLYWHEEL TO CRANK
2.4L only. Six (6) required.		 7.20
each
6102 BOLT, FRONT PULLEY, 2.0L-2.4L
 4.20
6103 WASHER, FRONT PULLEY, 2.0L-2.4L.
 15.60
6104 KEY WAY
On front crankshaft for front pulley and timing gears.		 2.40
6123 FREEZE PLUG
Steel 1.5L-1.9L.		 4.75
6131 FRONT PULLEY SLEEVE REPAIR KIT
Helps prevent serious oil leaks cause by a grooved pulley shaft.		 8.00
Engine block
Timing cover & chain and oiling system, 1.5L-2.4L
6021 OIL PUMP COVER WITH GASKET
This generally cures low oil pressure problems without having to replace costly gears. 1 .9L-2.4L.		 33.60
6022 OIL PUMP KIT
Includes oil pump cover with gasket and both oil pump gears. 1.9L-2.4L.		 126.00
set
6023 TIMING CHAIN
1.9L-2.4L.		 35.00
6024 TENSIONER KIT
Includes right and left timing chain guides, tensioner guide rail, and special hardware, 1.9L-2.4L. 		58.80
set
6032 SPECIAL BOLTS FOR LONG TIMING CHAIN RAIL
2 req. (already included in 6118 and 6024).		 3.60
each
6034 CUP
Oil pressure by-pass in oil filter area of timing cover.		 3.60
6044 OIL PRESSURE SENDER
New original Opel part. With rubber boot. 		126.00
6079 OIL PRESSURE SENDER, VDO
OEM replacement part. Without rubber boot. 		129.00
6105 TIMING CHAIN GEAR SET
One (1) upper and one (1) lower timing chain gear.Fits All CIH Opel engines 1.5L, 1.9L, 2.0L, 2.2L & 2.4L CIH.		 149.00
6118 TIMING CHAIN RAIL
New Opel Design Long timing chain rail with hardware. Reduces timing chain rattling.
Fits: All CIH Opel engines. 1.5L, 1.9L, 2.0L, 2.2L & 2.4L CIH.		 24.00
6119 TIMING CHAIN RAIL, SHORT UPPER
New Opel Design Short Upper timing chain rail. New design reduces the common timing chain rattle. Fits: All CIH Opel engines. 1.5L, 1.9L, 2.0L, 2.2L & 2.4L CIH.		 20.40
6120 TENSIONER ARM
Lower tensioner arm for the timing chain. Common wear item. Fits: All CIH Engines. 1.5L, 1.9L, 2.0L, 2.2L & 2.4L CIH.		 24.00
6127 HYDRAULIC TENSIONER
Hydraulic Tensioner, Fits: All CIH Engines. 1.5L, 1.9L, 2.0L, 2.2L & 2.4L CIH.		 60.00
6158 RELIEF PISTON
Oil pump cover pressure relief piston.		 6.00
1.9L Cylinder Head
Camshaft & Lifters

NOTE: New lifters must be used when installing a new camshaft. NEVER INSTALL USED LIFTERS ON A NEW CAM!

6026 CAM BUTTON 73-75
For heads with extra two Allen bolts in front. 1.9L-2.4L.		 4.00
6027 SOLID LlFTER
New. Must be replaced when installing new solid grind camshaft. Eight (8) required. Same as 6121.		 13.00
each
6028 HYDRAULIC LIFTER
New. Must be replaced when installing new hydraulic grind camshaft. Eight (8) required.		 14.50
each
6057 CAMSHAFT
Stock grind, 4 bearing. 1971-1974, hydraulic grind. 1.9L.		 150.00
6058 CAMSHAFT
HP "Torquer" .407" lift, 256 duration. Specify solid or hydraulic grind. 1.9L-2.4L. Good for street application.		 199.00
6059 CAMSHAFT
HP "Combination" .430" lift, 268 duration, solid or hydraulic grind. 1.9L-2.4L. Good for street and autocross applications.		 199.00
6060 CAMSHAFT
HP "Max Comp" .430" lift, 284 duration. Solid grind only. 1.9L-2.4L. Good for autocross and racing applications. Not for street!		 199.00
6061 CAMSHAFT
HP "Ultra Suer Comp" .480" lift, 300 duration. Solid grind only. 1.9L-2.4L. racing cam. Not for street! 		199.00
6045 CAM BEARINGS
Four (4) each 1971-1975, 1.9L, semi-finished, must be align bored.		 45.00
set
6046 CAM BEARINGS
Three (3) each 1968-1970 finished.		 45.00
set
Cylinder head
Valve train, 1.9L-2.4L
6029 ROCKER NUT
New original. Eight (8) required.		 3.00
each
6030 ROCKER ARM
New original. Eight (8) required.		 16.20
each
6031 ROCKER STUD
New original. Eight (8) required.		 9.00
each
6062 VALVE, INTAKE
Stock 39mm.		 11.00
each
6063 VALVE, EXHAUST
Stock 33 mm.		 19.00
each
6064 VALVE KEEPERS
Set of eight (8).		 9.50
set
6073 ROCKER ARM BEARING
1.9L-2.4L. Eight (8) required.		 6.40
each
6084 PLUG
Lifter galley in cylinder head. 4 req.		 2.40
each
6087 OIL DAM
Mounts in oil return hole in back of cylinder head. Increases camshaft oil bath level. Helps reduce cam to lifter ware. Excellent addition for all 1.9L-2.4L.		 14.00
6100 CAM BOLT
Camshaft to upper timing gear attaching bolt 1.9L-2.4L. Three (3) required.		 3.60
each
6135 SCREW WITH WASHER
For cam covers.		 .50
6543 INTAKE VALVE SPRING
1.9L - 2.0L. Intake Valve Spring.		 10.00
each
Cylinder head
Hardware, 1.5L-2.4L
6048 BOLT
Bolts intake/exhaust manifold to cylinder head. Six (6) required.		 4.20
each
6084 PLUG
Lifter galley in cylinder head. Four (4) required.		 2.40
each
6087 OIL DAM
Mounts in oil return hole in back of cylinder head. Increases camshaft oil bath level. Helps reduce cam to lifter ware. Excellent addition for all 1.9L-2.4L.		 7.20
6088 BOLT WITH SERRATED 8MM HEAD
Intake manifold to exhaust manifold. Four (4) required.		 3.00
each
6100 CAM BOLT
Camshaft to upper timing gear attaching bolt 1.9L-2.4L. Three (3) required.		 3.60
each
6126 HOSE
Crankcase ventilation to Weber air cleaner 9003. Allows clean routing of crankcase ventilation.		 3.00
6128 VALVE COVER CAP
Polished original. New.		 18.00
6135 SCREW WITH WASHER
For cam covers.		 .50
6137 THERMOSTAT HOUSING GASKET
2.2L-2.4L cylinder head.		 2.40
6138 INTAKE / EXHAUST GASKET
2.2L - 2.4L cylinder head.		 22.00
6139 HEADER GASKET
Made from high-temp REMFLEX material. For 2.2L-2.4L intake/exhaust.		 45.00
6150 HEAD TO TIMING COVER BOLT
Bolt from front cylinder head to timing cover, 1972-1994. Two (2) required.		 5.00
each
6153 GASKET OIL PICKUP TUBE
Gasket for the oil pickup tube, 1.9L-2.4L.		 1.00
6154 INTAKE VALVE 2.0L
Valve, 2.0L intake valve, 42 mm. Can be installed into a 1.9L head.		 28.00
each
6155 EXHAUST VALVE 2.0L
Valve, 2.0L exhaust valve, 36 mm. Can be installed into a 1.9L head.		 35.00
each
6156 VALVE STEM SEAL KIT
Valve stem seal kit. Contains four (4) intake seals and four (4) exhaust O-ring seals.		 15.00
6189 USED 2.0L CYLINDER HEAD
Factory big valve head with 43mm intake valves and 36mm exhaust valves. Special order item.		 350.00
SOI
Engine blocks, 1.9L-2.4L
6192 1900 ENGINE
Custom built to suit your needs! Call for details.		 Call for details
6201 2000 ENGINE
Remanufactured 2.0L engine. Long block. Direct bolt-up replacement for the Opel 1900. More torque and horsepower than a 1900. Stock with factory big valve head. Includes oil pan and complete timing cover assembly. 95mm bore, 70mm stroke. Special order item.		 Call for details
6221 2200 ENGINE
Remanufactured 2.2L engine. Long block. Direct bolt-up replacement for the Opel 1900. More torque and horsepower than a 2000. Factory 2.2L cylinder head. You provide your rear-sump oil pan and accessories. 95mm bore, 77.50mm stroke. Special order item.		 Call for details
1.5L GASKETS & SEALS
1.5L, 1968 only, 10-Bolt Cylinder Head type
6090 HEAD GASKET
Cylinder head to block, 1.5L.		 15.00
6091 HEAD GASKET SET
Cylinder head to block, 1.5L.		 45.00
6092 COMPLETE GASKET SET
1.5L.		 85.00
6006 INTAKE/EXHAUST GASKET
Intake/exhaust to cylinder head gasket, for 1.5L.Also fits 1.9L & 2.0L.		 13.00
6007 EXHAUST TO INTAKE GASKET
Between the intake and exhaust manifolds (hot spot gasket).		 2.50
6008 VALVE COVER GASKET
Valve cover to the cylinder head. Specify year if other than GT 1900 with aluminum valve cover.		 11.00
6009 OIL PAN GASKET
Oil pan to block.		 16.00
6010 WATER PUMP GASKET
Water pump to timing cover. 		5.60
6011 OIL PUMP GASKET
Oil pump cover to timing cover.		 2.40
6012 TIMING COVER GASKETS
Timing cover to block.		 12.00
set
6013 THERMOSTAT GASKET
Fits around thermostat.		 1.50
6014 THERMOSTAT HOUSING GASKET
Thermostat housing to cylinder head. 		2.40
6015 CAM COVER GASKET
Cam cover to head. Front or rear.		 3.00
6016 HEAD SIDE PLATE GASKET
Side plate to head.		 2.00
6017 FUEL PUMP GASKET
Fuel pump to timing cover. Two (2) required.		 1.20
each
6018 FRONT SEAL
Timing cover to pulley.		 12.00
6019 REAR MAIN SEAL 24.00
6020 O-RING SEAL
Timing cover to head, rubber.		 2.40
6051 FUEL PUMP SPACER
Spacer for between fuel pump and timing cover.		 6.60
6075 DISTRIBUTOR GASKET
Between timing cover and distributor.		 1.20
6090 HEAD GASKET
Cylinder head to block, 1.5L.		 15.00
6091 HEAD GASKET SET
Cylinder head to block, 1.5L.		 45.00
6092 COMPLETE GASKET SET
1.5L.		 85.00
6098 TIMING COVER GASKET SET
Includes front seal, water pump gasket and timing cover gasket set.		 25.00
6131 FRONT PULLEY SLEEVE REPAIR KIT
Helps prevent serious oil leaks cause by a grooved pulley shaft.		 8.00
10012 HEADER GASKET
Special REMFLEX high-temp gasket for early-style headers.		 45.00
ENGINE ELECTICAL
Starters, Alternator, Distributer, Coil & Ignition
5021 VOLTAGE REGULATOR
New OEM German part.		 49.00
5022 ALTERNATOR, REBUILT
Rebuilt 35 amp Opel alternator. Core fee $35, Your core return is required.		 129.00
6047 LOWER ALTERNATOR BUSHING
Two (2) required. 		5.40
each
6049 UPPER ALTERNATOR BUSHINGS
Between bracket and timing cover. Set of two (2). 		19.20
set
5022-65 ALTERNATOR, HI OUTPUT
Rebuilt stock Opel alternator with 65 amp internal components. Core fee $35, Your core return is required.		 165.00
5022-IR ALTERNATOR INTERNALLY REGULATED
Rebuilt Late 80's Opel high output internally regulated alternator, 45 amps.
You must have a good working amp meter warning circuit.		 149.00
5023 DISTRIBUTOR
Rebuilt. Specify year 1969-1974. Core required.		 99.00
5027 STARTER, REBUILT
Rebuilt Opel starter. Core fee $25, Your core return is required.		 149.00
5027PM HIGH TORQUE, PERMANENT MAGNET STARTER
If you have been looking for a powerful, reliable starter to crank over your 1.9 thru 2.4L them this brand new permanent-magnet Opel starter is for you.		 299.00
6040 SPARK PLUGS
L87YC for 1971-1975, four (4) required or L82YC for 1968-1970.		 2.00
each
6041 DISTRIBUTOR CAP AND ROTOR
Specify year.		 19.00
6042 CONTACT POINTS
Located inside distributor.		 9.00
6043 CONDENSER
Bosch. Specify round or square distributor entry hole. 		11.00
6071 IGNlTlON WIRE SET
Pre-cut spark plug and coil wires. 1.9L-2.4L.		 20.00
set
6077 PLATINUM SPARK PLUG
Bosch. Best spark plugs money can buy. Four (4) required.		 12.00
set
6078 DISTRIBUTOR CAP, COLORED
Transparent yellow, blue or red. Specify color. For 1970-1973.		 9.50
6134 POINTS
For 1975 FI dsitributor.		 9.00
6165 PERTRONICS POINTS CONVERSION IGNITION
Electronically controlled ignition trigger that eliminates the need for points and condensor improves throttle response. Simplifies tune-ups, gets rid of the points forever! Easy to install.		 99.00
UNDER HOOD PARTS
6035 FIREWALL MATERlAL
New firewall material to replace your old, torn or missing firewall mat. 		33.00
6036 HOOD PROD HOLDER
Holds hood prod when hood is closed. Polyurethane replacement part.		 3.50
6037 UNDER-HOOD RUBBER
Limits air flow over the radiator to help cooling, and helps keep engine fumes from entering the cars interior through the air vents, four (4) piece set.		 25.00
set
6038 HOOD RUBBER BUMPERS
Protects car body from hood when hood is closed. Four (4) required. 		3.50
each
1.1L GASKETS & SEALS
1.1L, 1968-1972
6093A HEAD GASKET
Cylinder head to block, 1.1L.		 20.00
6093 HEAD GASKET SET
Cylinder head to block, 1.1L.		 45.00
6095 COMPLETE GASKET SET
For 1.1L.		 85.00
6096 OIL PAN GASKET
Oil pan to block, 1.1L		 12.00
6097 VALVE COVER GASKET
Valve cover to cylinder head, 1.1L.		 6.00
6114 EXHAUST FLANGE GASKET
1.1L.		 2.00
6145 INTAKE GASKET
Intake to cylinder head, 1.1L.
 6.00
6146 EXHAUST GASKET
Exhaust to cylinder head, 1.1L.
 7.00
6149 BOTTOM END GASKET SET
Bottom end gasket set, 1.1L		 59.00
6157 PISTON RING SET 1.1L
1.1L piston ring set, for 4 pistions.		 45.00
1.1l Cylinder head
Valve train, 1.1L
6110 INTAKE VALVE
1.1L.		 5.00
each
6111 EXHAUST VALVE
1.1L.		 6.00
each
6112 VALVE KEEPERS
1.1L.		 0.10
each
6113 CAM BEARINGS
1.1L, STD.		 DISC
6115 INTAKE VALVE SPRING
1.1L.		 4.00
each
6116 EXHAUST VALVE SPRING
1.1L.		 4.00
each
1.1L ENGINE BLOCK
Timing cover & chain and oiling system, 1.1L
6080 1.1L TIMING CHAIN KIT
Includes gears, chain, gaskets, and hardware.		 95.00
6108 1.1L MAIN BEARINGS
Specify size STD, .25mm (.010"), .50mm (.020") and .75mm (.030")		 50.00
set
6109 1.1L ROD BEARINGS
Specify size STD, .25mm (.010") and .50mm (.020"). 		30.00
set
6125 CHAIN TENSIONER BLOCK
1.1L. Aftermarket.		 40.00
Previous page Next page
This page was last updated on Thu Apr 22 10:04:52 2010 PST